DSC Digital Security Control PC158O Dokumentacja

11.1 SpecificationsControl Panel SpecificationsFlexible Zone Configuration:• Six fully programmable zones• Seven Access Codes: five User, one Master a

KEYPADV COMMANDS10• [3] – Auto-Arm TimeThe system can be programmed to Auto-Arm at acertain time. When programming the auto-arming time,enter the time

KEYPADV COMMANDS11described below. A function is activated by pressing andholding the appropriate key for two seconds.“Stay” – Stay ArmPressing this k

12How to ProgramSECTION4The following section of the manual describes the Installer’sProgramming function and how to program the various sections.You

13HOWV TOV PROGRAMlight will turn OFF and the Armed light will turn ON.Refer to Section 5 in this manual to determine what eachoption represents and w

14Program DescriptionsThe following section explains the operation of all programmablefeatures and options and provides a summary of all corresponding

15P R O G R A M D E S C R I P T I O N S[09] 24 Hour Supervisory Zone (with LINKS)If this zone is violated when the system is either armed ordisarmed,

16P R O G R A M D E S C R I P T I O N S5.5 Communicator – Account NumbersThe account number is used by the central station todistinguish between pane

17P R O G R A M D E S C R I P T I O N SOpening (Disarming) Reporting Codes ... Section [42]Opening After Alarm Keypad RingbackSection [6

18P R O G R A M D E S C R I P T I O N SAfter a Delinquency Code has been transmitted, itwill not send again until the system has been armedand disarm

19P R O G R A M D E S C R I P T I O N Skey (Hex [C]).The panel has no way of confirming if the pager was calledsuccessfully; a Failure To Communicate

SYSTEMV INTRODUCTION2The LINKS 1000 is only supported by the NorthAmerican AMPS Network and is not supported bythe European GSM Network.1.2 Additional

20P R O G R A M D E S C R I P T I O N SThe PGM will activate when any of the following eventsoccur and will remain active for as long as the keypadbu

21P R O G R A M D E S C R I P T I O N Salarm in any way and the Bell will remain silent but the Panicsignal will be sent to the central station. This

22P R O G R A M D E S C R I P T I O N SThe Fire, Auxiliary, Panic keys will operate even ifKeypad Blanking is active (See Section 5.21 “Key-pad Blank

23P R O G R A M D E S C R I P T I O N SSwinger Shutdown ...Section [62]5.19 Event BufferThe panel will s

24P R O G R A M D E S C R I P T I O N S• if unsuccessful, the panel will try to call using the landlines• if unsuccessful, the panel will try to call

25For the RecordCustomer:_______________________________________________________________________________________Address:______________________________

26Keypad Programming[00] Keypad Assignment (Section 2.5 “Keypad Assignment”)Note::::: This must be done at each keypad requiring programming.[0] Slo

27[03] Installer’s Code (Section 4 “How to Program”)Default Default1575 I_______I_______I_______I_______I or 157500 I_______I_______I_______I_______II

28P R O G R A M M I N G W O R K S H E E T S[10] Third System Option CodeDefault Option ON OFF SectionOFFI________I 1 Arm / Disarm Bell Squawk Enabled

29NOTE::::: For sections [31] to [46], the contents of every section by default is [F].[31] First Telephone Number (32 Digits) (Section 5.6 “Communic

3Getting StartedSECTION2The following Sections provide a thorough description of how towire and configure devices and zones.2.1 Installation StepsThe

30[42] [42] [42] [42] [42] Opening (Disarming) Reporting Codes, Access Codes 1-6 (Section 5.7 “Communicator – ReportingCodes”)I_______I_______I Openin

31[53] Openings & Closings Communicator Call Directions (Section 5.4 “Communicator – Dialing”)Default Option ON OFFONI________I 1 1st Telephone Nu

32[68] LINKS 1000 Preamble (Second Telephone Number) (Section 5.24 “LINKS 1000 Cellular Communicator”)Default: FFFFI_______I_______I_______I_______I (

33[82] Second International Options CodeDefault Option ON OFF SectionOFFI_______I 1 European Dialing Parameters North American Dialing Parameters 5.4O

Contact IDThe Partition ID Codes must be 4 digits. All reporting codes must be 2 digits.The following is a list of Contact ID reporting codes. The fir

Appendix BSIA FormatLevel 2 (Hardcoded)The SIA communication format used in this product follows the level 2 specifications of the SIA Digital Communi

Appendix CAppendix CPROGRAMMINGV LCDV KEYPADSProgramming LCD KeypadsIf you have an LCD5500 Keypad, additional programming is required for proper opera

[62] Third User Display MaskDefault Option ON OFFONI_______I 1 System Test prompt ON System Test prompt OFFONI_______I 2 Time and Date prompt ON Time

38LIMITED WARRANTYDigital Security Controls Ltd. warrants the original purchaser that for a period of twelvemonths from the date of purchase, the prod

PC1580 CONTROL PANEL WIRING DIAGRAM✁Control Panel Wiring DiagramTMIncorrect connections mayresult in fuse failure or improperoperation. Inspect wiring

G E T T I N G S T A R T E D4Programmable Outputs – PGM1 and PGM2Each PGM output is designed sothat when activated by the panel, theterminal will swit

© 1998 Digital Security Controls Ltd.1645 Flint Road, Downsview, Ontario, Canada M3J 2J6Tel. (416) 665-8460 • Fax (416) 665-9310Printed in Canada

InstallationManualPC158O• W A R N I N G •This manual contains information on limitations regarding product useand function and information on the limi

FCC COMPLIANCE STATEMENTCAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use th

Table of ContentsSection 1 – System Introduction 11.1 Specifications... 11.2 Additional

TABLE OF CONTENTSTABLEV OFV CONTENTS5.15 Arming / Disarming Options... 225.16 Entry / Exit Delay Options ...

G E T T I N G S T A R T E D5which slots are occupied in order to generate a fault whena supervisory is not present.How to Assign KeypadsEach keypad m

G E T T I N G S T A R T E D62.8.4 Fire Zone Wiring — Four-Wire Smoke DetectorsAll fire zones must be wired according to the followingdiagram:2.8.5 Ke

7Keypad CommandsSECTION3The PC1580 alarm panel can be accessed, controlled andcompletely programmed via any keypad on the system. TheLED keypad uses f

KEYPADV COMMANDS8If the Code Required for Bypass option is enabled, onlyuser codes with the Bypass attribute enabled will be able tobypass zones (see

KEYPADV COMMANDS9reporting code(s) programmed in section [45] will betransmitted along with the unreported events from anearlier unsuccessful communic