DSC PC560 Dokumentacja

1TABLE OF CONTENTSINTRODUCTION 3Features ...

10[∗]+[8]+[Installer’s Code]: Installer’s Programming CommandThe PC560 is programmed from the keypad by using commands in the [∗][8][Installer’s Code

11PROGRAMMING GUIDEWith the panel disarmed, enter [∗][8][Installer’s Code]. The panel can only be programmed while it isdisarmed. The default Instal

12Resetting Programming to the Factory Default SettingsThe system may be reset to its factory default programming by following this procedure:1 Remove

13PROGRAMMING SECTIONS[01] Zone DefinitionsEnter four 2-digit numbers in this section to determine the operating characteristics of each zone.Zone Def

14[02] System TimesThree system times are programmed in Section [02]; each time requires a 3-digit number. Do not press the [#]Key during data entry.

15[05] First System Option CodeWhen Section [05] is entered, the 4 Zone Lights will be ON or OFF to indicate which options are selected.To turn a Zone

16[07] Third System Option CodeRefer to Section [05] for programming information.LIGHT[1] • ON = Restorals reported on Disarming*OFF = Restorals repor

17[13] Maintenance and Priority CodesMaintenance Codes are transmitted to indicate various trouble conditions and their restorals; Priority Codesare u

18FOR THE RECORDCustomer ___________________________________________________________________________________Address __________________________________

19[01] Zone Definitions Page 13NOTE: When defining zones, assign Delay Zones starting with Zone 1, then Zone 2, and so on.Then, assign the other z

2PROGRAMMING GUIDE 11Sections [05] through [07]: Enabling System Functions ... 11HE

20[06] Second System Option Code Page 15Default Zone Light ON Zone Light OFFON Zone Light 1 DTMF dialing Pulse dialingOFF Zone Light 2 1400Hz Hands

21[11] Zone Alarm and Restoral Reporting Codes Page 16For single digit reporting codes, enter [0] as the second digit.Zone 1 Alarm Enter [∗1∗] (HEX

22[13] Maintenance and Priority Codes Page 17[P] Key Alarm[A] Key Alarm[F] Key AlarmBattery TroubleBattery RestorePeriodic Test CodePolice Code[14

23HOOK-UP DIAGRAMWWW.DIYALARMFORUM.COM

LIMITED WARRANTYDigital Security Controls Ltd.’s liability for failure to repair the prod-uct under this warranty after a reasonable number of attempt

WARNING Please Read CarefullyNote to InstallersThis warning contains vital information. As the only individual in contactwith system users, it is your

© 1997 Digital Security Controls Ltd.1645 Flint Road, Downsview, Ontario, Canada M3J 2J6Printed in Canada 29000870 R3WWW.DIYALARMFORUM.COM

InstallationManualPC56O• W A R N I N G •This manual contains information on limitations regarding product use andfunction and information on the limit

3INTRODUCTIONFEATURES• Fully featured security system with TroubleSupervision, Alarm Memory, Master Code and 3programmable Access Codes, Quick-Arming

4INSTALLATIONMounting the PanelSelect a dry location close to an unswitched AC source, a ground connection, and the telephone connection.Remove the pr

5WiringNOTE: Complete all wiring to the control panel before applying battery or AC power.If the neutral in the main supply is not readily identifiab

6KEY Terminal ConnectionThe KEY terminal may be programmed for keyswitch operation or for use as a tamper zone. Refer to theHook-up Diagram in the ba

7KEYPAD FUNCTIONSIntroductionThe Keypad provides complete control of the PC560 control panel. The panel can be completely programmedfrom the keypad.

8DisarmingEnter the premises through the designated Entry-Exit door. The keypad will be sounding a tone to indicate thatthe system must be disarmed.

9[∗]+[3]: Display Alarm MemoryAlarms caused during the previous armed period are stored in memory. To display the zones that went intoalarm, enter [