DSC PC 1555 Instrukcja Instalacji Pobierz pdf (Strona 21)

’Chime’ - Door Chime On/Off

Pressing the key will toggle the Door Chime feature ON

or OFF. One solid beep means the feature has been dis-

abled, three short beeps means it has been enabled.

’Reset’ - Reset Smoke Detectors

Pressing this key will cause the panel to activate for 5 sec-

onds any output programmed as Sensor Reset.

(

see sec-

tion ’[*] [7] Command Output Functions’

’Exit’ - Activate Quick Exit

Pressing this key will cause the panel to activate the Quick

Exit feature

(

see section ’[*] [0] Quick Exit’

Function Key Options

The programming of any function key on any keypad

may be changed to one of the options listed below (see

section 2.6 ‘Keypad Assignment‘ for instructions on

changing function key programming.)

[00] - Null Key

The key is not used and will perform no function when

pressed.

[01] - Not Used

[02] - Not Used

[03] - Stay Arm

Same as described in Function Keys - Section 3.5.

[04] - Away Arm

Same as described in Function Keys - Section 3.5.

[05] - [*]+[9] No Entry Delay Arm

After this function key is pressed the user must enter a

valid access code. The system will arm and remove entry

delay from the system when the Exit Delay expires

(

see

section ’[*] [9] Arming Without Entry Delay’

)

[06] - [*]+[4] Door Chime On/Off

This function key provides the user a simple method for

turning the Door Chime feature on and off

(

see section ’[*]

[4] Door Chime On/Off’

)

[07] - [*]+[6]...[4] System Test

This function key provides the user with a simple method

for testing the system

(

see section ’[*] [6] User Functions’

)

A valid Master Code is required to perform this com-

mand.

[08] - [*]+[1] Bypass Mode

This function key provides the user with a simple method

for entering the Bypass Mode. If an access code is

required it must be entered before bypassing can be per-

formed

(

see section ’[*][1] Zone Bypassing’

)

[09] - [*]+[2] Trouble Display

This function key provides the user with a simple method

for entering the Trouble Display mode

(

see section ’[*][2]

Trouble Display’).

[10] - [*]+[3] Alarm Memory

This function key provides the user with a simple method

for entering the Alarm Memory Display mode

(

see sec-

tion ’[*] [3] Alarm Memory’

)

[11] - [*]+[5] Programming Access Codes

This function key provides the user with a simple method

for programming access codes. After this key is pressed a

valid System Master or Supervisor Code will have to be

entered before the panel will allow programming to be

performed

(see section 4.2 ‘[*] Commands‘)

[12] - [*]+[6] User Functions

This function key provides the user with a simple method

for programming user functions. Once this key is pressed a

valid System Master Code or Partition Master Code must

be entered before the panel will allow User Functions to be

performed

(section 4.2 ‘[*] Commands‘)

[13] - [*]+[7]+[1] Command Output Option 1

This function key provides the user with a simple method

for activating a PGM output programmed as Command

Output Option 1

(see Section 5.8, Programmable Output

Programming)

. By default, after this key is pressed a valid

access code must be entered

(section 4.2 ‘[*] Commands‘)

[14] - [*]+[7]+[2] Smoke Detector Reset

This function key provides the user with a simple method

for activating a PGM output programmed as either option

[03] Sensor Reset or [20] Command Output option 2.

[15] - General Voice Prompt Help

This feature can only be programmed if both the

Escort5580(TC) and the PC5936 audio matrix module are

being used.

When the function key is pressed, the intercoms will per-

form a Help page. The user must then press the Page/

Answer button on any intercom station to begin the help

session with the Escort.

For more information, see the

PC5936 Installation Man-

ual

NOTE:

While the voice prompt help is active, users will not

be able to disarm the system using wireless keys.

[16] - [*]+[0] Quick Exit

Same as described in ‘Function Keys’ - Section 3.5.

[17] - [*]+[1] Reactivate Stay/Away Zones

This function key provides the user with a simple method

for adding Stay/Away zones back into the system

(sec-

tion 4.2 ‘[*] Commands‘)

[18] Identified Voice Prompt Help

This feature can only be programmed if the

Escort5580(TC) and the PC5936 audio matrix module are

being used.

When the function key is pressed, the Escort5580(TC) will

begin a help session from the intercom station pro-

grammed as closest to the keypad. In order for this option

to function, you must program PC5936 Section [802], sub-

section [14] ’Keypad Port Assignments.’ For more infor-

mation, Refer to the

PC5936 Installation Manual

NOTE:

This function key cannot be programmed for

PC55XXZ LED keypads with software version 1.0.

NOTE:

While the voice prompt help is active, users will not

be able to disarm the system using wireless keys.

[19] - [*]+[7]+[3] Command Output 3

[21] - [*]+[7]+[4] Command Output 4

Function keys [19] and [21] provide the user with a sim-

ple method of activating an output programmed as Com-

mand Output Option 3 or 4.

[22] - NOT USED

[23] - Bypass Recall

Pressing this function key will recall the last group of

bypassed zones. The function key will follow the Code

CodeCode

Code

Required for Bypass

Required for BypassRequired for Bypass

Required for Bypass option. If the option is enabled, a

valid access code with the Bypass attribute enabled must

be entered after the function key is pressed. For instruc-

tions on zone bypassing, see the

Power Series User Guide

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 55 56

Komentarze do niniejszej Instrukcji

Brak uwag

DSC PC 1555 Instrukcja Instalacji Strona 21

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa DSC PC 1555