DSC PTK5507 Instrukcja Użytkownika

PTK5507 v1.0 TouchscreenUser ManualNOTE: Use these instructions in conjunction with the Installation Manual of the alarm panel with which this equip-m

6Intrusion (Burglary) Alarm Continuous SirenIf you are unsure of the source of the alarm, approach with caution! If the alarm was acciden-tal, enter y

7Zone StatusThis screen allows you to view the status of the zones on the system.Figure 5 - Zone Closed Zones areClosed (Restored)Ready – the zone is

8Trouble – the alarm panel has detected a technical problem with one or more components of the alarm system e.g., loss of AC power. (See Troubles on p

9Low Battery – one or more modules in the zone has a low battery. (See Figure 9 on page 9.)Figure 9 - Low BatteryLowBattery Bypassed Zones Use the zon

10TroublesWhen a trouble condition is detected, the Trouble ( ) or System indicator will turn on, and the keypad will beep every 10 seconds. Press the

11Alarm MemoryWhen an alarm occurs, the Memory or System indicator will turn on. To view which sensor(s) generated the alarm, press Alarms . The senso

12OutputsYour installer may have programmed these keys to perform various functions (reset smoke detector after an alarm, open your garage door, etc.)

13Access CodesWhen Access Codes is selected from the Options menu, the keypad prompts for a Master Code. When a valid Master Code is entered, a numeri

14Partition Assignment Mask ([][5][Master/Supervisor Code][98][Code])1. Partition One Access (available for PC1616/PC1832/PC1864)2. Partition Two Acc

15System Test The system’s Bell Output (2s), Keypad Lights and Communicator are tested. This test will also measure the panel’s

16Clean Mode – allows the user to touch (i.e., clean) the screen without enabling or disabling any func-tions. The screen will remain in this mode for

17Partition StatusTo view the partition status, press Options, User Functions, then Partition Status. The keypad shows basic status for up to 8 partit

18Reference SheetsFill out the following information for future reference and store this guide in a safe place.System InformationEnabled?  [F] FIRE 

19Access CodesPC1616/PC1832/PC1864Master Code [40]: _________________________CodeAccessCodeCodeAccessCodeCodeAccessCodeCodeAccessCode01 13 25 4202 14

Sensor Protected Area Sensor Type Sensor Protected Area Sensor Type01 3302 3403 3504 3605 3706 3807 3908 4009 4110 4211 4312 4413 4514 4615 4716 4817

21Testing Your SystemNOTE: If you are going to perform a System Test, call your Monitoring Station to inform them when you begin and also when you end

22Guidelines for Locating Smoke Detectors and CO DetectorsThe following information is for general guidance only and it is recommended that local fire

236. In the living area(s) of a residential board and care occupancy (small facility).Figure 2Figure 1Figure 3Figure 3aFigure 4Carbon Monoxide Detecto

242. Study the possible escape routes from each location within the house. Since many fires occur at night, special attention should be given to the e

Table of ContentsWelcome Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Emergency Key . . . . . . .

IMPORTANT - READ CAREFULLY: DSC Software purchased with or without Products and Components is copyrighted and is purchased under the following license

27IN THIS LICENSE AGREEMENT, DSC’S ENTIRE LIABILITY UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL BE LIMITED TO THE GREATER OF THE AMOUNT ACTUAL

© 2012 Tyco International Ltd. and its Respective Companies. All Rights Reserved.Toronto, Canada • www.dsc.com • Printed in CanadaThe trademarks,

Always ensure you obtain the latest version of the User Guide. Updated versions of this User Guide are available by con-tacting your distributor.IMPOR

1IMPORTANT NOTICEA security system cannot prevent emergencies. It is only intended to alert you and, if included, your central station of an emergency

2Welcome ScreenThe date & time are displayed in the upper right corner of the screen. The system status (i.e., Ready, Armed, Exit Delay etc.) is d

3Figure 3 - Controls & IndicatorsTime/DateTrouble MenuCommand OutputKeypad/Security FunctionsEmergency KeyPartition StatusSystem StatusStay ArmGlo

4Figure 4 - Keypad If Disarm is selected during the exit delay, a numeric keypad is displayed.• Enter (tap) your access code. • The arming sequence

5DisarmIf Disarm is selected:• A numerical keypad is displayed.• Enter your Access Code in the keypad.• The system returns to the Home screen and t