DSC Power832 PC5O15 Instrukcja Instalacji Pobierz pdf (Strona 28)

P R O G R A M D E S C R I P T I O N S

25

1st Phone Number .................................................. Section [301]

2nd Phone Number ................................................. Section [302]

3rd Phone Number ................................................. Section [303]

3rd Phone Number Enable ..................................... Section [380], Option [5]

Alternate Dial .......................................................... Section [380], Option [6]

5.5 Communicator - Account Numbers

There are two Partition Identifier Codes (or Account Numbers) programmable, one for each Partition. The

Account Number is used by central station to determine which panel is calling.

If the panel is programmed as two Partitions both Account Numbers must be programmed. The panel will report

to the central station by Partition. For example, if an alarm occurs on a zone assigned to Partition 1 the panel will

report using Partition 1 Account Number.

Partition 1 Identifier Code ...................................... Section [310]

Partition 2 Identifier Code ...................................... Section [311]

5.6 Communicator - Reporting Formats

Each central station phone number of the panel can be programmed to report using any one of the 5 formats

available. The following formats are supported: Pulse (10 and 20 BPS), Contact ID, SIA, Residential Dial and a

Pager format. The following is a description of each:

5.6.1 Pulse Formats

Depending on the pulse format selected the panel will communicate using the following:

• 3/1, 3/2, 4/1 or 4/2 • 1400 or 2300 Hz handshake • 10 or 20 bits per second • non-extended

Additional Notes on Pulse Formats

1. The digit ‘0’ will send no pulses and is used as a filler.

2. When programming account numbers enter four digits.

3. When programming a three digit account number the fourth digit must be programmed as a plain ‘0’ which will

act as a filler digit.

4. If an account number has a ‘0’ in it, substitute a HEX digit ‘A’ for the ‘0’. Examples:

• 3 digit account number [123] - program [1230] • 3 digit account number [502] - program [5A20]

• 4 digit account number [4079] - program [4A79]

5. When programming reporting codes two digits must be entered. If one digit reporting codes are to be used

the second digit must be programmed as a ‘0’. If a ‘0’ is to be transmitted substitute a HEX digit ‘A’ for the ‘0’.

Examples:

• 1 digit reporting code [3] - program [30] • 2 digit reporting code [30] - program [3A]

6. To prevent the panel from reporting an event program the reporting code for the event as [00] or [FF].

This communication forThis communication for

This communication for

mat cannot be selected if Downlook is rmat cannot be selected if Downlook is r

mat cannot be selected if Downlook is r

equirequir

equir

ed.ed.

ed.

Communicator Format Options .............................. Section [360]

5.6.2 Contact ID

Contact ID is a specialized format that will communicate information using tones rather than pulses. This format

allows more information to be sent faster than other formats. For example, in addition to reporting an alarm in

zone one, the Contact ID format will also report the type of alarm, such as an Entry/Exit alarm.

If the

Contact ID uses Programmed Reporting CodesContact ID uses Programmed Reporting Codes

Contact ID uses Programmed Reporting Codes option is enabled, a two digit number from Appendix A

must be entered in programming sections [320] to [353] for each event to be transmitted. The two digit number

determines the type of alarm. The panel will automatically generate all other information, including the zone

number.

If the

Contact ID uses Automatic Reporting CodesContact ID uses Automatic Reporting Codes

Contact ID uses Automatic Reporting Codes option is enabled, the panel will operate as follows:

1. If an event’s reporting code is programmed as [00], the panel will not attempt to call the central station.

2. If the reporting code for an event is programmed as anything from [01] to [FF], the panel will automatically

generate the zone or access code number. See Appendix A for a list of the codes which will be transmitted.

If the Automatic Contact ID option is selected, the panel will automatically generate all zone andIf the Automatic Contact ID option is selected, the panel will automatically generate all zone and

If the Automatic Contact ID option is selected, the panel will automatically generate all zone and

access code numbers, eliminating the need to praccess code numbers, eliminating the need to pr

access code numbers, eliminating the need to pr

ogram these items.ogram these items.

ogram these items.

If the

Contact ID uses Programmed Reporting CodesContact ID uses Programmed Reporting Codes

Contact ID uses Programmed Reporting Codes option is enabled, the panel will operate as follows:

1. If an event’s reporting code is programmed as [00] or [FF], the panel will not attempt to call central station.

2. If the reporting code for an event is programmed as anything from [01] to [FE], the panel will send the

programmed reporting code.

Additional Notes on Contact ID

1. Account numbers must be four digits.

2. All reporting codes must be two digits.

3. Substitute the HEX digit ‘A’ for the ‘0’.

4. To prevent the panel from reporting an event, the reporting code should be programmed as [00].

DSC Power832 PC5O15 Instrukcja Instalacji Strona 28

Komentarze do niniejszej Instrukcji

DSC Power832 PC5O15 Instrukcja Instalacji Strona 28

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa DSC Power832 PC5O15