DSC Power832 PC5O15 Instrukcja Instalacji Pobierz pdf (Strona 37)

P R O G R A M D E S C R I P T I O N S

exists.

(See Section 5.17 “Swinger Shutdown”.)

The event buffer can be viewed three different ways. It can be viewed through an LCD keypad, printed on-site using

the PC5400 printer module

(See Section 5.29 “On-Site Printer”)

or it can be uploaded through the DLS software.

5.16.1 Viewing the Event Buffer

The following is the procedure for viewing the event buffer through the LCD keypad:

Step 1 - Enter [✱] [6] [Master Code]

Step 2 - Select ‘View Event Buffer’

The keypad will display the Event Number, Partition, Time and Date of the event in question. Use the [✱] key to toggle

between this information and the event itself. Use the arrow keys (<>) to scroll through the events in the buffer.

When you have finished viewing the event buffer press the [#] key to exit.

Event Buffer Follows Swinger Shutdown ............... Section [013], Option [7]

5.17 Swinger Shutdown

The swinger shutdown feature is designed to prevent a runaway communicator from tying up the central station.

Different limits can be programmed for Zone Alarms, Zone Tampers

and Maintenance

signals. After the panel

has communicated the programmed number of transmissions for an event it will no longer report that event until

the swinger shutdown is reset.

For example, the swinger shutdown limit for Zone Alarms is set to [003]. The panel will not send more than 3

alarm signals for each zone with a swinger attribute until the swinger shutdown is reset.

The Bell output will not be activated for alarms on zones that have exceeded the limit of alarms set in the

Swinger Shutdown counter.

Swinger Shutdown

will be reset when the panel is armed or every day at midnight. Once reset, the panel will

again communicate normally.

Swinger Shutdown Limit (Alarms/Tampers/Maintenance) Section [370]

5.18 Daylight Savings Time

If the Daylight Savings Time

option is enabled, the panel will follow the daylight savings time change. At 2 a.m.

on the first Sunday in April, the panel clock will be set forward one hour to 3 a.m. At 2 a.m. on the last Sunday in

October, the panel clock will be set back one hour to 1 a.m.

Events prEvents pr

Events pr

ogrammed to occur between 2 and 3 a.m. will not occur on the first Sunday in April. Eventsogrammed to occur between 2 and 3 a.m. will not occur on the first Sunday in April. Events

ogrammed to occur between 2 and 3 a.m. will not occur on the first Sunday in April. Events

prpr

ogrammed to occur between 1 and 2 a.m. will occur twice on the last Sunday in Octoberogrammed to occur between 1 and 2 a.m. will occur twice on the last Sunday in October

ogrammed to occur between 1 and 2 a.m. will occur twice on the last Sunday in October

Daylight Savings Time ............................................ Section [017], option [6]

5.19 Keypad Backlighting

The keys of all the keypads can be backlit to provide easy viewing in dim lighting conditions. If the Keypad

Backlighting Option

is enabled the keys will be illuminated.

Keypad Backlighting Option ................................... Section [016], Option [5]

5.20 Arming /Disarming Options

If the Arm/Disarm Bell Squawk option is enabled the panel will squawk the alarm output once upon arming and twice

upon disarming. The Opening After Alarm Keypad Ringback option will give you the ability to beep the keypad 8

times rapidly if the panel is disarmed after an alarm occurred. The Opening After Alarm Bell Squawk

option will give

you the ability to squawk the bell output 8 times rapidly if the panel is disarmed after an alarm occurred.

Closing Confirmation, if enabled, will cause the keypad to beep 8 times rapidly after the closing reporting code

has been successfully transmitted to central station.

If the Bypass Status Displayed While Armed option is chosen, the Bypass light will be ON while the system is

armed to indicate that there are bypassed zones.

If the panel is armed using the Stay function key, or by entering [✱][9][access code], there will be no bell

squawks during entry and exit delays, except for the arm/diarm bell squawks.

If the panel is arIf the panel is ar

If the panel is ar

med using the Stay function key thermed using the Stay function key ther

med using the Stay function key ther

e will be no bell squawks during the exit delaye will be no bell squawks during the exit delay

e will be no bell squawks during the exit delay

except for the arexcept for the ar

except for the ar

m bell squawk. If the panel is no-entrm bell squawk. If the panel is no-entr

m bell squawk. If the panel is no-entr

y ary ar

y ar

med using [med using [

med using [

✱

][9][access code], ther][9][access code], ther

][9][access code], ther

e will bee will be

e will be

no bell squawks during the exit delayno bell squawks during the exit delay

no bell squawks during the exit delay

, except for the ar, except for the ar

, except for the ar

m/disarm/disar

m/disar

m bell squawks. Therm bell squawks. Ther

m bell squawks. Ther

e is no entre is no entr

e is no entr

y delayy delay

y delay

(and no bell squawks) when the panel is no-entr(and no bell squawks) when the panel is no-entr

(and no bell squawks) when the panel is no-entr

y ary ar

y ar

med.med.

med.

If WLS Key Uses Access Codes is enabled, the disarm button will

not

work on wireless keys which have not been

assigned access codes. (Please see your PC5132 manual for more information on programming wireless keys.)

This option must be enabled when using a PC5132 v2.1 or earlierThis option must be enabled when using a PC5132 v2.1 or earlier

This option must be enabled when using a PC5132 v2.1 or earlier

. Ther. Ther

. Ther

eforefor

efor

e, Section [017] option [1]e, Section [017] option [1]

e, Section [017] option [1]

must be ON.must be ON.

must be ON.

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 47 48

Komentarze do niniejszej Instrukcji

Brak uwag

DSC Power832 PC5O15 Instrukcja Instalacji Strona 37

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa DSC Power832 PC5O15