DSC Power832 Security System PC5016 Dokumentacja Pobierz pdf (Strona 30)

P R O G R A M D E S C R I P T I O N S

[10] Latched System Event

The PGM output will activate when any of the selected events occur. It will deactivate when an access

code is entered. Global alarms must be silenced with a global code.

The normal PGM attributes, programmed in Sections [141] to [154] is replaced with the following list for

any output selected as Latched System Event:

Light [1] Burglary......... Delay, Instant, Interior, Stay/Away and 24 Hour Burglary Zones

Light [2] Fire ................ Fire Keys, Fire Zone (PGM Output)

Light [3] Holdup .......... Holdup zones and Duress alarms

Light [4] Medical ......... Auxiliary Keys, Medical and Emergency Zones

Light [5] Supervisory ... Supervisory, Freezer and Water Zones

Light [6] Priority ........... Gas, Heat, Sprinkler and 24 Hour Latching Zones

Light [7] Partition 1 PGM enable ]

Either or both of these lights should be ON to indicate

Light [8] Partition 2 PGM enable ]

which Partition(s) will activate the PGM output.

[11] System Tamper

The PGM Output will activate when any Tamper condition is present and will deactivate when all Tamper

conditions are cleared.

[12] TLM and Alarm

The PGM Output will activate when a telephone line fault condition is present AND an alarm occurs. The

PGM Output will remain active until an access code is entered. The output will activate for both audible

and silent alarms if a TLM trouble is present.

This output will activate for all audible and silent alarms except Duress.

[13] Kissoff

The PGM Output will activate for two seconds after the panel receives the kissoff from the central station.

[14] Ground Start

The PGM Output will activate for two seconds before the panel attempts to dial to obtain dial tone on

Ground Start telephone equipment. Two 2-second pauses should be inserted at the beginning of the

phone number when using this option.

Main Board PGM Outputs ............................. Section [009]

PC5208 PGM Output Options ....................... Section [010]

PC5204 PGM Output Options ....................... Section [011]

5.10.2 PGM Output Attributes

Each Programmable Output also requires the PGM Attributes to be programmed before they will operate

correctly. Attributes available are as follows:

PGM Options 2, 3, 5-7 PGM Options 1, 8, 11-16

Option [1] - ON Partition 1 Controls Event Option [1] - Must be ON

OFF Partition 1 Does Not Option [3] - ON Output Activates on Event

Option [2] - ON Partition 2 Controls Event OFF Output Deactivates on Event

OFF Partition 2 Does Not

Option [3] - ON Output Activates on Event

OFF Output Deactivates on Event

The Attribute Options for Option [09] System Trouble and [10] Latched System Event are

different. Refer to these options for more information.

PGM1 (Main Board) Output Attributes .......... Section [141]

PGM2 (Main Board) Output Attributes .......... Section [142]

PC5208 PGM Output Attributes .................... Section [143] to [150]

PC5204 PGM Output Attributes .................... Section [151] to [154]

5.11 Telephone Line Monitor (TLM)

The panel will supervise the presence of the phone line and indicate a trouble condition if disconnected. If

TLM Enabled

is selected the panel will wait the TLM Trouble Delay

time before indicating the trouble so

that a momentary interruption of the phone line will not cause a trouble condition.

The TLM Trouble Only

or Audible When Armed

option will allow you to select if the panel will indicate a

trouble condition at the keypad or indicate a trouble at the keypad when disarmed and activate the alarm

output when armed.

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 43 44

Komentarze do niniejszej Instrukcji

Brak uwag

DSC Power832 Security System PC5016 Dokumentacja Strona 30

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa DSC Power832 Security System PC5016