DSC SYSTEM MASTER PC4000 Instrukcja Obsługi Pobierz pdf (Strona 9)

USER FUNCTIONS COMMAND

[✱]+[6]+[ACCESS CODE]

Enter [✱][6][Access Code] and then use the [<][>] keys to display the items of the

function menu. Press [✱] to select an item.

[0]Quick Arm [1]Quick Exit [2]Auto Arm Control [3]Keypad Setup

[4]Bell/Comm Test [5]Door Chime [6]Spec. Messages [7]User Call Up

[8]View Partitions

Item [0], [1], [5] and [6] turn on and off various functions. To enable or disable these

functions, press the [✱] key to toggle “Y ”or “N” on the keypad.

Y - The function is enabled

N - The function is disabled

NOTE

: The Auto Arm time is a 24 hour clock and times must be entered as two digit

numbers.

E.g. HH - 01, 02,.....10,11,.....23,24

MM - 00, 01,.....35,36.....58,59

Enter 4 digits representing the time in hours and minutes (HH:MM) based on 24 hour

or military time. Always enter a leading zero where only one digit is required, 8:05 am

would be entered as 0805, 1:30 pm would be entered as 1330.

QUICK ARM

[✱]+[6]+[ACCESS CODE]+[0]

The “Quick Arm” feature is enabled by toggling to “Y” on the keypad. When enabled

the panel can be armed by entering [✱][0].

QUICK EXIT

[✱]+[6]+[ACCESS CODE]+[1]

The “Quick Exit” function is enabled by toggling to “Y” on the keypad. When enabled

the user can exit through any delay zone without altering the status of the system, by

entering [✱][0] on the keypad.

AUTO ARM CONTROL

[✱]+[6]+[ACCESS CODE]+[2]

The PC4000 can be programmed to arm a partition at the same time each day, by

enabling the Auto Arm function and programming the Auto Arm time.

At the selected Auto Arm time, the system will give a pre-alert. The keypad begins

to sound and the Bell/Siren will pulse once every 10 seconds to alert anyone on the

premises that the system is about to arm. The Bell/Siren pulse can be programmed

by the installer to be silent.

The keypad will sound for one minute before Auto Arming unless the Auto Arm is

aborted. To abort the Auto Arm and silence the keypad press any key during the

pre-alert. The Auto Arm will be attempted at the same time the following day. The

PC4000 can be programmed to require a code to be entered for a user to abort the

Auto Arm by the installer.

Upon selecting the Auto Arm Control function, the Auto Arm Control menu will

appear on the LCD keypad.

[0] Auto Arm [1] Auto Arm Time

Auto Arm toggles “Y” or “N” to enable or disable the Auto Arm function.

Auto Arm time is the time the partition will automatically arm itself every day.

ALARM MEMORY DISPLAY

[✱]+[3]

Press [✱] then [3] to enter the alarm memory mode. Any alarm caused during the

last armed period will be displayed. The “Alarm Memory” message will only be

displayed when an alarm occurred during the last armed period.

Press [#] to return to “READY”.

USER PROGRAMMING COMMANDS

[✱]+[5]+[MASTER CODE]

The [✱][5] Access Codes programming command is used to program additional

access codes of any type.

The PC4000 has 128 access codes. In the Installer’s Programming Section, these

codes can be divided up and assigned to partitions, or are turned into System

Master Codes, which have control over all partitions. This must be done before the

user can program the access code and the code type.

The first code is the System Grand Master Code. Only the Installer can change this

code, unless the Installer has enabled the user to change the System Grand Master.

There are 11 types of codes:

System Grand Master Code has no limitations to its use. It can create or delete

other System Master Codes or perform any other user feature the PC4000 user is

capable of doing. Only the first access code (Access Code 001) can be a System

Grand Master.

System Master Codes can do anything on the system. They can be used to

bypass, view memory, view trouble, etc. They may be used to create or delete any

type of code except for System Master Codes.

Partition Master Codes has unlimited access to their own partition. These types of

codes can create, delete or alter any code type in their partition other than System

Masters. They can only assign users to their own partition.

Arm/Disarm/Bypass Access Code may arm, disarm or bypass on the partition

to which it has been assigned.

Arm/Disarm Access Code can only be used to arm or disarm the partition to

which it has been assigned.

Arm Only Access Code can only arm the partition to which it has been assigned.

Door Strike Code can only activate [✱][7] utility output on the partition it belongs to if

the partition is disarmed.

Log Only Code will only put a record on to the event buffer.

Arm/Disarm/OTU Code is erased when used to arm.

Arm Only OTU Code is erased when used to arm.

Door Strike OTU Code is erased after used.

NOTE

: OTU stands for One Time Use.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 19 20

Komentarze do niniejszej Instrukcji

Brak uwag

DSC SYSTEM MASTER PC4000 Instrukcja Obsługi Strona 9

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa DSC SYSTEM MASTER PC4000