DSC Power8 PC5OO5 Instrukcja Instalacji Pobierz pdf (Strona 32)

P R O G R A M D E S C R I P T I O N S

A General System Supervisory Trouble Reporting Code will be transmitted if any module goes missing from the

Keybus. If the module is a zone expander the panel will also transmit the Zone Expander Supervisory Alarm

Trouble Reporting Code. The panel will send a General System Supervisory Restoral Reporting Code when the

problem is corrected as well as a Zone Expander Supervisory Restoral Reporting Code if the module is a zone

expander.

5.7.8 Test Transmissions

The panel can be programmed to transmit a Periodic Test Transmission

Reporting Code

(See Section 5.13 “Test

Transmissions”)

, a System Test Reporting Code

(See Section 3.4 “[

✱

] Commands, [

✱

] [6]”)

or a LINKS1000 Test

Transmission Reporting Code

(See Section 5.26 “LINKS1000 Cellular Communicator”).

5.7.9 Wireless Maintenance

The panel will transmit a General Zone Low Battery Alarm Reporting Code if a low battery condition is indicated

by a detector. The transmission of the trouble will be delayed by the number of days programmed for Zone Low

Battery Transmission Delay. The General Zone Low Battery Restoral Reporting Code will be transmitted when

the problem is corrected. The specific zone that caused the trouble will be stored to the Event Buffer.

The restoral will not be transmitted until all detectors indicate a good battery condition.

5.7.10 Miscellaneous

The panel will transmit the Keypad Lockout Reporting Code if the lockout is activated

(See Section 5.22

“Keypad Lockout”)

The DLS Lead In Reporting Code will only be transmitted if the DLS Call Back feature is being used

(See Section

5.8 “Downloading”)

. Before the panel calls the computer back it will call central station and transmit the reporting

code to indicate a download session is about to begin. After downloading is complete the panel will transmit a DLS

Lead Out Reporting Code to indicate the download session is complete.

If the panel fails to transmit information to the central station it will display a failure to communicate trouble

condition. The panel will transmit a Phone Number 1 Failure to Communicate Reporting Code or a Phone

Number 2 Failure to Communicate Reporting Code the next time it calls the central station. The panel will

transmit the old events, followed by the failure to communicate, followed by the new events. This will allow

central station to determine which events are old or new.

If the Event Buffer is uploaded on a regular basis an Event Buffer 75% Full Reporting Code can be transmitted

to warn the Buffer is almost full. This is also useful if the PC5400 Printer Module is being used.

The Delinquency reporting code is sent whenever the panel is not armed within the number of days

programmed for the Delinquency Transmission Delay.

If the Delinquency Transmission Delay is set for one day, there must be 24 hours of no arming or

disarming before the Delinquency Code will be sent.

After a Delinquency Code has been transmitted, it will not send again until the system has been

armed and disarmed.

5.7.11 Activity Delinquency

When Delinquency Follows Zone Activity is enabled, if there is no activity on zones in the system, the

Delinquency Transmission Cycle Timer in Section [370] will begin counting in hours. When the counter reaches

the programmed time, the panel will communicate the Delinquency reporting code to the central station, if

programmed. If there is zone activity present on the system at any time, the counter will be reset. If this option

is used, the Delinquency Follows Arming option is not available.

Activity Delinquency will not be reported while the panel is armed in Away mode.

Activity on bypassed zones will not reset the timer. PGM2 activation will not reset the timer.

This timer is reset when the panel is armed, or if Installer Programming is entered.

When using the SIA FSK communication format with Activity Delinquency, the Closing Delinquency

identifier is transmitted.

Reporting Codes .................................................... Sections [320] to [353]

Delinquency Follows Zone Activity ......................... Section [380], Option [8]

Delinquency Transmission Cycle .......................... Section [370]

5.8 Downloading

Downloading allows programming of the entire control panel via a computer, modem and telephone line. All

functions and features, changes and status, such as trouble conditions and open zones can be viewed or

programmed by downloading.

When power is applied to the panel, a 6 hour or 1 hour downloading window can be enabled. This will

allow you to perform downloading without having to do any keypad programming.

If the Answering Machine Override

option is enabled (or during the first 6 hours after power up) the panel

will answer incoming calls for downloading provided the following conditions occur:

1. The panel hears one or two rings then misses a ring.

2. At this point the panel will start a timer.

3. If the panel hears another ring before the Answering Machine Double Call Timer

expires it will answer on

the first ring of the second call.

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 45 46

Komentarze do niniejszej Instrukcji

Brak uwag

DSC Power8 PC5OO5 Instrukcja Instalacji Strona 32

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Systemy kontroli dostępu bezpieczeństwa DSC Power8 PC5OO5